ProForm 8.0 Zt Treadmill Manuel d'utilisateur

SerialNumberDecalModel No. PFTL49509.0Serial No.Write the serial number in the spaceabove for future reference.CAUTIONRead all precautions and instruc

109. Set the console assembly face down on a softsurface to avoid scratching the console.Carefully pivot the Console Frame (111) to theposition shown.

1112. Start an M8 x 25mm Patch Bolt (5) and two5/16" x 5/8" Patch Bolts (113) with two M8 StarWashers (10) into the Right Upright (89) andRi

1215. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clearplastic on the treadmill decals, remov

13OPERATION AND ADJUSTMENTTHE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Nev

14FEATURES OF THE CONSOLEThe treadmill console offers an impressive array offeatures designed to make your workouts more effec-tive and enjoyable. Whe

15HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed tocold temperatures, allow it to warm to room tem-perature before turning on th

165. Change the incline of the treadmill as desired.To change the incline of the treadmill, press theIncline increase or decrease buttons or one of th

17HOW TO USE A CALORIE WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page 15.2. Select a calorie workout.To select a calor

18HOW TO USE A PERFORMANCE WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page 15.2. Select a performance workout.To select

19HOW TO USE AN IFIT WORKOUTTo purchase iFit cards, go to www.iFit.com or call thetelephone number on the front cover of this manual.iFit cards are al

TABLE OF CONTENTSWARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20THE INFORMATION MODEThe console features an information mode that keepstrack of the total distance that the walking belt hasmoved and the total numb

21HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGEBefore folding the treadmill, adjust the incline to thelowest position. If yo

22TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur

23Remove the three M4.2 x 19mm Hood Screws (12)and carefully pivot the Motor Hood (67) off.Locate the Reed Switch (70) and the Magnet (51)on the left

PROBLEM: The walking belt is off-center or slips when walked onSOLUTION: a. If the walking belt is off-center, first remove thekey and UNPLUG THE POWE

25These guidelines will help you to plan your exerciseprogram. For detailed exercise information, obtain areputable book or consult your physician. Re

26PART LIST—Model No. PFTL49509.0 R0210ATo locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.Key No. Qty. Descriptio

27Key No. Qty. Description Key No. Qty. Description101 1 Right Handrail102 1 Console Ground Wire103 1 Console Base104 1 Left Accessory Tray105 1 Conso

4629625842434445616059718155554515218151642664282864266341636136321481495632472727575750481292929292929294965505361717115115728EXPLODED DRAWING A—Mode

671312131213121746833767219206197225216777114808182338384111111116970117875333079223940EXPLODED DRAWING B—Model No. PFTL49509.0 R0210A29

31. Before beginning any exercise program, con-sult your physician. This is especially impor-tant for persons over age 35 or persons withpre-existing

5858724232492389879239233197199592319973190888893949498869093339691923510113101091103737113114811430EXPLODED DRAWING C—Model No. PFTL49509.0 R0210A

103413810410614100372353529810199981073566105551010108108343737373737373735353535107661113473733310211231EXPLODED DRAWING D—Model No. PFTL49509.0 R021

Part No. 292610 R0210A Printed in China © 2010 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, please see the front cover of this m

419. Never leave the treadmill unattended while itis running. Always remove the key, unplugthe power cord, and switch the reset/off cir-cuit breaker t

5Thank you for selecting the new PROFORM®8.0 ZTtreadmill. The 8.0 ZT treadmill offers a selection of fea-tures designed to make your workouts at home

6ASSEMBLYTo hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.Assembly requires two persons. Set the treadmill in a

71. Make sure that the power cord is unplugged.With the help of a second person, carefully tipthe treadmill onto its left side. Partially fold theFram

83. Remove the M10 x 50mm Bolt (31), the M10 Nut(19), and the shipping bracket (A) from the Base(95). Attach a Wheel (97) with the Bolt and theNut tha

96. With the help of a second person, carefully tipthe treadmill onto its right side. Partially fold theFrame (56) so that the treadmill is more stabl