Model No. PFTL49909.0Serial No.CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manualfor future ref
107. Set the console assembly face down on a softsurface to avoid scratching the console assem-bly. Hold the Right Handrail (33), which has alarge hol
11119. Attach the console assembly to the Uprights(53, 54). Start all six M8 x 15mm Bolts (8) withsix M8 Star Washers (5) into the Uprights.Then, firm
1212. See the lower drawing. Position the Uprights(53, 54) so that the Frame (51) is centered be-tween them.Firmly tighten the two M10 x 60mm Patch Bo
1314. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clearplastic on the treadmill decals, remov
14OPERATION AND ADJUSTMENTTHE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Nev
15KeyClipCONSOLE DIAGRAMFEATURES OF THE CONSOLEThe treadmill console offers a selection of features de-signed to make your workouts more effective. Wh
16HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed tocold temperatures, allow it to warm to room tem-perature before turning on th
17The lower left display—As you exercise, thelower left display canshow the elapsed timeand the distance that youhave walked or run. Inaddition, the d
18HOW TO USE A PRESET WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page 16.2. Select one of the six preset workouts.To se
19THE INFORMATION MODEThe console features an information mode that keepstrack of treadmill usage information and allows you toselect a unit of measur
TABLE OF CONTENTSWARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGEBefore folding the treadmill, adjust the incline to thelowest position. If yo
21HOW TO LOWER THE TREADMILL FOR USE1. Hold the frame with your right hand as shown. Pull the latchknob to the left and hold it. Pivot the frame downw
22TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur
23Locate the Reed Switch (89) and the Magnet (62) onthe left side of the Pulley (71). Turn the Pulley until theMagnet is aligned with the Reed Switch.
24PROBLEM: The crosswalk arms squeak during useSOLUTION: a. (Note: Correcting this problem requires a smallamount of white marine grease, available at
25These guidelines will help you to plan your exerciseprogram. For detailed exercise information, obtain areputable book or consult your physician. Re
2612M10 x 60mm Patch Bolt24M10 x 75mm Bolt32M4.2 x 13mm Tek Screw4 13 M4.2 x 16mm Screw56M8 Star Washer61Latch Warning Decal72M5 Star Washer86M8 x 15m
27Key No. Qty. Description Key No. Qty. Description101 2 Drive Roller Washer102 3 M4.2 x 18mm Screw103 1 Console Fan104 2 M10 x 58mm Bolt105 2 Cage Nu
EXPLODED DRAWING A—Model No. PFTL49909.0 R0909A9317818651766728628938393631462525252575755625716828186119442729553621422129603619422744191978644504141
EXPLODED DRAWING B—Model No. PFTL49909.0 R0909A3438447934305938669020202037996547474757212142422110887104231047258928240492110029
3IMPORTANT PRECAUTIONS1. Before beginning any exercise program, con-sult your physician. This is especially impor-tant for persons over age 35 or pers
EXPLODED DRAWING C—Model No. PFTL49909.0 R0909A8010235411531419111149481033772288772423988577101010771010101084857106105105524963261343321332431066969
31EXPLODED DRAWING D—Model No. PFTL49909.0 R0909A159173412103444444444116116117110113119981138411011811998
Part No. 287651 R0909A Printed in China © 2009 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, please see the front cover of this m
419. The treadmill is capable of high speeds.Adjust the speed in small increments to avoidsudden jumps in speed.20. Never leave the treadmill unattend
5Thank you for selecting the new PROFORM®CROSS-WALK 2.0 XT treadmill. The CROSSWALK 2.0 XTtreadmill offers a selection of features designed to makeyou
ASSEMBLYTo hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.Assembly requires two persons. Set the treadmill in a
72. Have a second person hold the Base (52) in theposition shown.Identify the Right Upright (54), which has asquare hole near the lower end.Hold the R
84. Position the Base (52) as close to the front of thetreadmill as possible, as shown.See the upper inset drawing. Locate the wiretie in the lower en
96. See the left inset drawing in step 5. Identifythe outer side of the remaining Frame Spacer(11).Hold the Frame Spacer (11) between the LeftUpright
Commentaires sur ces manuels